HP Laserjet M600 Series M601, M602< M603 Common Paper Jam Pasadena
A paper jam is often a term employed to summarize when prints becomes lodged inside of a HP Laserjet Printer which is not able of ejecting. When this takes place the HP Laserjet Printer is not going to work correctly until the paper has been physically cleared.
13.00 Paper Jam
Information
Undetermined door open
Solution::
ensure eachl of the covers & doors are shut.
13.A3 Paper Jam
Overview
Power on paper jam right within Tray 3 feed sensor.
Solution:
Examine the product for a paper jam. Note the clear paper jams section inside service repair manual.
13.D3 Paper Jam
Overview
Delay to reach duplex re-feed jam
13.D3.D1 Paper Jam
13.D3.D2 Paper Jam
13.D3.D3 Paper Jam
13.D3.D4 Paper Jam
13.D3.D5 Paper Jam
13.D3.D6 Paper Jam
13.D3.DD Paper Jam
13.D3 Paper Jam
Solution:
Search the HP product for a paper jam. Note the clear paper jam page In the service handbook.
13.E5 Paper Jam
Overview
A startup paper jam has occured.
Solution:
Check the HP Printing product for a paper jam.
13.EA Paper Jam
Overview
An open door jam has happened.
Solution:
Examine the product for any paper jam.
Use the component test to determine a bad door / cover switch or sensor.
13.EE Paper Jam
Overview
A power up paper jam has taken place.
Solution:
Examine the HP printer for the paper jam.
13.FF Paper Jam
Overview
A door jam has taken place.
Solution:
Look through the HP Product for a paper jam.
Turn to the Manual sensors analysis and / or Tray/Bin manual sensors check to determine a faulty door switch as well as sensor.
13.WX Paper Jam
Overview
This particular jamming happens when a door is opened during printing.
Solution:
Confirm that the doors are fully closed.
13.WX Paper Jam
Overview
Power on residual paper jam
This jam appears when the paper is present at the paper path jam sensors at power on or door close.
Because the most recent Firmware timing requirement, the demonstrated jam code is always 13.FF.FF, only the event log will display 13.WX.FF
Solution:
Look through the HP Product for a paper jam.
13.WX Fuser Area Jam
Overview
A paper jam in the fusing assemlby region has manifested.
Solution:
Clear the jam.
Verify media meets technical specs, check for obstructions within fuser, check that the T2 roller is
set up securely.
13.WX Fusing Assembly wrap around jam
Overview
Solution:
take out the jam.
13.WX Paper Jam below control panel
Overview
◦ 13.B2.9Z (event code)
Page at duplex switchback jam.
Z = the source tray number
Solution:
Examine the HP Product for any jam.
13.WX Paper Jam in Tray 1 Manual Feed
Overview
◦ 13.B2.D1 (event code)
Delayed to registration paper jam, from Tray 1
This jam arises anytime the media fails to get through the TOP sensor in specified amount of time from the start of media pick-up at printing from manual feed tray & duplex printing.
Solution:
Clear out the jam.
13.WX Paper Jam in Tray <X>
Overview
A misfeed paper jam has appeared.
Solution:
Clear the jam.
13.WX jam under envelope feeder
Overview
A jam rests on the inside of the envelope feeder.
Solution:
Eliminate the jam.
13.WX Paper Jam underneath} top cover
Overview
A jam exist within the top cover.
Solution:
Remove the paper jam.
14.00.
Overview
A feed / separation roller problem has appeared.
◦ 14.00.01
◦ 14.00.02
◦ 14.00.03
◦ 14.00.04
◦ 14.00.05
◦ 14.00.06